Featured Products
Great news for Arduino Nano owners!!! We're excited to launch these new add-on modules for the Arduino Nano. They enhance the ability of the Arduino Nano while maintaining breadboard friendliness and ease of quick prototyping. Below are some of the modules. More to come soon! ETHERNET-4NANO: Open Arduino Nano to the internet. MP3-4NANO: Play MP3 files on the Micro-SD card. USBHOST-4NANO: Open communication to USB devices. XBEE-4NANO: Wireless communication with ability to update firmware OTA. 2MOTOR-4NANO: Enables mechanical projects to control up to two DC motors and has built-in feedback loop circuitry. Get yours today! |
This add-on module allows you to connect the Arduino Nano to the internet. You get all of the benefits of using the Arduino Nano. This includes breadboard friendliness for quick prototyping. It is fully assembled with long pin headers so you don’t need to purchase and solder the headers separately. You’re ready to go out of the box. Yes, you get the same stackable benefits as the Arduino shields and can run the same code. $39.95, 10/$359.60, 50/$1,598.00 |
This add-on module allows you to play MP3 files using the Arduino Nano. You get all of the benefits of using the Arduino Nano. This includes breadboard friendliness for quick prototyping. It is fully assembled with long pin headers so you don’t need to purchase and solder the headers separately. You’re ready to go out of the box! $39.95, 10/$359.60, 50/$1,598.00 |
Looking for project to interface with Android* phone and tablet? This add-on module allows you to interface with USB devices using the Arduino Nano. The communication is compatible with full and low-speed USB devices – mice, keyboards, joysticks, cameras, Android* devices and more. You get all of the benefits of using the Arduino Nano. This includes breadboard friendliness for quick prototyping. It is fully assembled with long pin headers so you don’t need to purchase and solder the headers separately. You’re ready to go out of the box! $24.95, 10/$224.60, 50/$998.00 |
Want to update your Arduino Nano firmware OTA (over-the-air)? This add-on module allows you to interface with XBee wireless module using the Arduino Nano. You can use it for wireless communication and wireless firmware update. You get all of the benefits of using the Arduino Nano. This includes breadboard friendliness for quick prototyping. It is fully assembled with long pin headers so you don’t need to solder and purchase the headers separately. You’re ready to go out of the box! $24.95, 10/$224.60, 50/$998.00 |
This add-on module allows you to control up to two DC motors at maximum of 2A/motor using the Arduino Nano. You get all of the benefits of using the Arduino Nano. This includes breadboard friendliness for quick prototyping. It is fully assembled with long pin headers so you don’t need to purchase and solder the headers separately. You’re ready to go out of the box! $29.95, 10/$269.60, 50/$1,198.00 |
Flyport is a revolutionary Wi-Fi module based on the open source platform openPICUS. It is a Wi-Fi compact module (only 35*48mm) designed around the Microchip PIC 24FJ256GA106 processor (256K Flash,16K Ram,16 Mips) and MRF24WB0MA/RM WI-FI Certified Transceiver. It is very easy to use; comes with many references/examples and free IDE! $99.00, 10/$891.00 |
FiO Std is a breadboard friendly development board using RapidSTM32 technology which base on a Simulink device driver blockset and tool suite for STM32 microcontroller family. Ultimately, the blockset is expected to enable users to transfer their designs from Simulink, with just one click, to a working embedded system (based on STM32 microcontrollers) without the need to write a single line of C or Assembly code. The blockset works by taking advantage of the Mathworks Inc.'s products, i.e. Real-Time Workshop and Real-Time Workshop Embedded Coder, code generation capability. $99.00, 10/$891.00 |
Looking for PICAXE programmer breakout board? This board breakout PICAXE programmer pins for ease of use. This Stereo Jack 3.5mm breakout board bring all 4 pins of a 3.5mm stereo jack out to screw terminal blocks for easy connection and prototyping work (1.left, 2. right, 3. ground, 4. jack present detection). The connections are also available via 0.1" header pins. $6.99, 10/$62.91 |
Looking for Microchip ICD breakout board? This board breakout MPLAB ICD3 or MPLAB REAL ICE PIC programmer for ease of use. This RJ11 breakout board bring all 6 pins of a 6P6C modular jack out to screw terminal blocks for easy connection and prototyping work. The connections are also available via 0.1" header pins. $6.99, 10/$62.91 |
This breakout board bring all 15 pins of a DB15 VGA connector plus a chassis pin out to screw terminal blocks for easy connection and prototyping work. The connections are also available via 0.1" header pins. We've included a male header strip with the item. $9.99, 10/$89.90 |
This breakout board bring all 25 pins of a DB25 female connector plus a chassis pin out to screw terminal blocks for easy connection and prototyping work. The connections are also available via 0.1" header pins. $16.99, 10/$152.90 |
This breakout board bring all 25 pins of a DB25 male connector plus a chassis pin out to screw terminal blocks for easy connection and prototyping work. The connections are also available via 0.1" header pins. $16.99, 10/$152.90 |
The BOT120 PICAXE 20x2 Microbot is a simple to assemble kit that uses a unique design which requires no soldering of wires to build and/or reconfigure a versatile robot. $74.95, 10/$674.60 |
The Netduino is an open source electronics platform using the .NET Micro Framework. It features a 32-bit microcontroller and a rich development environment. The Netduino combines 20 GPIOs with SPI, I2C, 2 UARTs, 4 PWMs, and 6 ADC channels. $34.95, 10/$314.60 |
The Netduino Mini is an open source electronics platform using the .NET Micro Framework. It features a 32-bit microcontroller (the same one used in the Netduino) and has a rich development environment. The Netduino Mini has a total of 16 GPIOs with SPI, I2C, UART, 4 PWMs, and 4 ADC channels. $29.95, 10/$269.60 |
The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip providing a network (IP) stack capable of both TCP and UDP. Regular price: $43.99 Sale price: $38.00 |
This is a simple, but very powerful stepper motor with a 4-wire cable attached. It is 1.8 degrees step angle, 2 phase, 12V, 2.3kg*cm with 5mm diameter drive shaft. $14.95, 10/$134.60 |
No more cutting and soldering!
This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive male barrel jack. $2.75, 10/$24.80, 100/$220.00 |
No more cutting and soldering!
This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positive female barrel jack. $2.75, 10/$24.80, 100/$220.00 |
This is the new Arduino Uno. In addition to all the features of the previous board, the Uno now uses an ATmega8U2 instead of the FTDI chip. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. $28.95 |
This is the new Arduino Uno Mega 2560. In addition to all the features of the previous board, the Uno Mega 2560 now uses an ATmega8U2 instead of the FTDI chip. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. It also has twice as much flash memory. $63.99 |
The new exciting high-performance STM32F103 Development Board. This board is packed with features and power, utilizing the latest microcontroller technology with the new ST Microelectronics STM32F103 Microcontroller based on the high-performace 32-Bit ARM Cortex-M3 Processor running up to 90 MIPS. $69.99 |
This is a potentiometer or variable resistor. It is open up many interesting user interfaces. Turn the pot and the resistance changes. Connect VCC to an outer pin, GND to the other, and the center pin will have a voltage that varies from 0V to VCC depending on the rotation of the pot. The pot is linear meaning the resistance will vary linearly with its position. This is a good choice for general user interfaces. If you need a logarithmic potentiometer see here. $1.99, 10/$18.00 |
This breakout board bring the 2 pins of a BNC connector out to screw terminal blocks for easy connection and prototyping work. The connections are also available via 0.1" spaced through-holes. This is perfect for breadboard or discrete wires. This breakout board is perfect for field wiring tasks and may be mounted to wall box plate or thin panel that has a BNC cutout. It is design to be 50 Ohm impedance. $4.99, 10/$44.90 |
Having a hard time running discrete wires to your breadboard? The wires kept falling out of the bread board? Here is the solution! This breakout board bring the 3 pins of a terminal block to 0.1" spaced through-holes. This is perfect for brining discrete wires to the breadboard. $2.99, 10/$26.90 |
Ever wonder what goes on inside these things? Well this clear transparency breadboard might enlighten. Beyond the clear plastic, this is really just a regular, solderless breadboard. It has 2 power buses, 30 columns, and 10 rows - a total of 400 tie in points. All pins are spaced by a standard 0.1". The two sets of five rows are separated by about 0.3", perfect for straddling a DIP package over. The board accepts wire sizes in the range of 19-28AWG. $4.99, 10/$44.90, 100/$399.00 |
The ScrewShield extends all pins of the Arduino out to 3.5mm pitch screw terminals. It also has a large prototyping space of both connected and unconnected 0.1" spaced through-holes. $16.95, 10/$152.60 |
The Arduino Mega now has its very own prototyping shield! The MegaShield mates with the Arduino Mega board and gives the user a prototyping area, two general LEDs, and, most important of all, the Arduino Mega reset switch is brought to the top level. $17.95, 10/$161.60 |
The SerIO is a serial interface platform for creating physical computing projects controlled from a computer. The board gives access to 14 digital input and output pins, six analog output pins and eight analog input pins through a serial interface. This allows the creation of physical computing projects wihtout having to modify and code on the hardware platform. $44.95, 10/$404.60 |
The Joystick Shield kit contains all the parts you need to enable your Arduino Duemilanove with a joystick! The shield sits on top of your Arduino and turns it into a simple controller. Five momentary push buttons (4+ joystick select button) and a two-axis thumb joystick gives your Arduino functionality on the level of old Nintendo controllers. $11.99, 10/$107.90 |
This is a force sensitive resistor with a round, 0.5" diameter, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. $6.95, 10/$62.60 |
This is a force sensitive resistor with a square, 1.75x1.5", sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area. $7.95, 10/$71.60 |
BlueBee is XBee adapter for the BlueScreen. It contains two of 10-pin 2mm-pitch connectors for Digi’s Xbee module. Including with on-board footprints for various types of sensor, it supports temperature and humidity sensor SHT11 (or SHT15), ambient light sensor TPS852 and absolute pressure sensor (and also temperature) SCP1000. $24.99 |
This is a breakout board for the Blackberry Trackball. The four spindles on the trackball have a tiny circular magnet the end; each of these are paired with an SMD hall effect sensor, which are used to measure up, down, left and right movements of the trackball. An SMD momentary switch is placed under the trackball to give you a select switch. $16.95, 10/$152.60, 50/$678.00 |
This is a new design LCD with dual 16-pin rows. For ease of use, it can be hooked up to top or bottom row. They are wiring in parallel. Use both rows to help secure onto the breadboard. It is an industry standard HD44780 based controlled 4 lines x 20 characters LCD display with BLACK characters on WHITE background and backlight. Regular price: $17.95 Sale price: $15.95 |
Lowest cost FT232RL Breakout Board! Packed with a quailty design. This is a breakout board for popular FTDI USB to UART IC (FT232RL). It allows you to use your PC to communicate with and power your project for up to 500mA (3.3V or 5V). The jumper on the board allows you to quickly change the logic levels (3.3V or 5V). It is breadboard friendly (0.1" spacing). All pins are labeled for ease of use. The design is properly included ferrite bead and other filter capacitors as FTDI recommended. Three LEDs telling you the status of RX (red), TX (green) and POWER (blue). $12.99 |
Reasons to shop from us
Welcome to our site. We pride ourselves in supplying innovative, unique and economical products. We are providing excellent and prompt solutions to your electronic projects."
Our goal is to provide and deliver technically innovative electronic experimental solutions for a broad range of hobbyists and developers. All of our products are engineered to save you both time & money for development a new project.
Our staff is eager to answer your questions. We give great and fast turn around on our e-mail support. We are looking forward to do business with you and help you develop your next project.
Our goal is to provide and deliver technically innovative electronic experimental solutions for a broad range of hobbyists and developers. All of our products are engineered to save you both time & money for development a new project.
Our staff is eager to answer your questions. We give great and fast turn around on our e-mail support. We are looking forward to do business with you and help you develop your next project.
